Why say closed cooling tower is energy saving and environmental protection equipment, more and more users are using this kind of equipment to replace the original equipment (open tower), we can through data analysis and comparison, the two energy data accounting can be obvious. Energy consumption is basically two major aspects, one is water, the other is electricity. Both are energy costs that no cooling tower can escape, unless you leave the equipment on.
First of all, look at the consumption of water. Water is generally consumed in two aspects. One is the flying overflow after spraying, and the other is the evaporation consumption of water.
Let's look at the open cooling tower, the spray water of the tower is basically between two and three percent of the overflow rate, if we according to the daily operation of 10 hours, excluding holidays, 280 days of operation. According to the actual open cooling tower flow of 6000 cubic meters per hour to calculate. 6000*2%*10*280= 336,000 tons of water, and the same closed cooling tower, its spray flying overflow is very small, because after all, the spray work is carried out in the tower, almost can be controlled in a few thousandths, we calculate according to 5 thousandths, the same is 10 hours of work, 280 days a year operation, To achieve the same cooling amplitude is basically 4,500 tons per hour of closed cooling tower is enough, then the calculation results: 4,500 *0.5%*10*280= 63,000 tons, it is not difficult to see, because of the different design structure caused by the waste of spraying water resources, more than 200,000 tons of terror. The bigger the pool of the open tower, the more wasted water, because the evaporation area increases, and the closed cooling tower has no pool, so the consumption here is zero. Judging from the price of a ton of water, just such a equipment, a year to solve the capital of hundreds of thousands of enterprises.
Let's look at the comparison of electric energy, electric energy is not different, because they are all through the same power equipment to operate the equipment, the power of the two is similar, the running time is the same, basically the energy consumption is about the same.
To sum up, for the closed cooling tower energy saving accounting can be strong to open the tower out, and, today are advocating energy conservation and environmental protection, this is the general trend, so the closed cooling tower is more and more favored by the majority of users.
Closed Cooling Tower,Closed Circuit Cross Flow,Closed Loop Cooling Tower,Closed Circuit Cooler Wuxi Ark Fluid Science Technology Co., Ltd. , https://www.fangzhou-arkfluid.com
Application:
PVC Plastic pipe making machine is mainly used in the production of Agricultural water supply & water discharge system, architectural water supply & discharge system, wire laying system, etc. purposes.Â
The unit consists of Conical (Parallel) double screw extruder-PVC pipe mold-Vacuum forming tank-Haul-off machine-Cutting machine-Stacker/Belling machine.Â
Producing pipe diameter range: Φ16mm-Φ630mm.
And the line can be equipped with Comptroller thickening instrument or computer ink-jet printer, etc. to achieve the production and manufacture of high-grade tubing.
Advantages:
1. Specified screw design for better material plasticizing &mixing effect, For high filling formula, bimetallic screw and barrel can guarantee perfect solution;
2. Spider type die head can reduce joint line of the melt material, with reasonable compression ratio design;
3. Vertical integrated structured gear box with adopts NSK/SKF bearings guarantee stable operation and long uselife;
4. Vacuum calibration tank adopts high-efficiency two chamber and large length design, providing faster calibration and more efficient cooling;
5. Planetary cutter adopts hydraulic feeding of blade which providing perfect chamfering processing and cutting surface;
6. U type, R type and Air blow type socket can be provided according to applications;
7. Intelligent PLC controlling system with human-friendly interface make the operation easily and conveniently.
Work flow and detailed information :
Feeder
- To feed material into extruder;
Extruder
- World famous brand electrical component such as Siemens,Schneider, ABB etc;
- High torque gearbox with adopts NSK/SKF bearing;
- Siemens/WEG original motor achieved global after service;
- Bimetallic screw and barrel;
- Intelligent PLC controlling system with human-friendly interface.Â
Die head
-Â High melt homogenity
-Â Low pressure built up even with high outputs
-Â Melt channel distribution system
-Â Equipped with seramic heaters
-Â Pipe head carriage for easy movement
-Â Easy maintenance thanks to the optimized and proven designed construction.
Vacuum calibration tank
-Â 304 stainless steel with painted outer surface
-Â Special water sprays are located on the best position for cooling the pipe efficiently
-Â Special and easy adjusted pipe supports for each pipe diameter
-Â Installed vacuum and water pumps can work without any maintenance for long times
-Â Special cooling baths can be designed for specific extrusion production
Haul off
- Upper and lower caterpillar is driven separately by the frequency inverter
- Fast change type pads
Planetary cutter
-Â Automatic synchronisation with extrusion speed
-Â Planetary equipped with disk and milling cutter for cut and chamfering
-Â Touch screen control panel
-Â User friendly software developed by Aceextech
-Â All movements are motorised and controlled by control panel
-Â Pipe blocking vices device
-Â Type of the cutting unit is chose depend on pipe.
-Â Less maintenance needs.
-Â Completely closed and secured machine for maximum safety.
Belling machine
-Â Socket forming: smooth (solvent cemented)
-Â Socket forming: shaped for insertion of rubber gasket (blowing system)
-Â Socket forming: collapsible system
-Â Socket forming: auto-load rubber gasket
-Â Touch screen control panel
-Â User friendly software developed
-Â Automatic synchronisation with extrusion speed
-Â Pneumatic, hydraulic and motorized movements.
-Â High quality belling tools.
Stacker
- Stainless steel 304 as touching material
- Discharge driving by air cylinder
Technical Parameter:
Diameter ranges(mm)
Extruder model
Max. Capacity(kg/h)
Max. lineal speed(m/min)
Extruder motor power(kw)
16-32 (4-cavities)
ACE65/132
300
10*4
37
20-63Â (Dual)
ACE65/132
300
15*2
37
50-160
ACE65/132
300
8
37
75-250
ACE80/156
500
6
55
110-315
ACE80/156
500
4
55
75-160 (Dual)
ACE92/188
850
6
110
315-630
ACE92/188
850
1.2
110
Technical Parameter of Main extruder:
Model
Power
(kw)Screw Diameter (mm)
Screw Qty.
Designed Output (kg/h)
Dimension(L*W*H)
(mm)
ACE-45/90
15
Φ45/90
2
70
3360x1290x2127
ACE-51/105
18.5
Φ51/105
2
100
3360x1290x2127
ACE-55/110
22
Φ55/110
2
150
3620x1050x2157
ACE-65/132
37
Φ65/132
2
300
3715x1520x2450
ACE-80/156
55
Φ80/156
2
400
4750x1550x2460
ACE-92/188
110
Φ92/188
2
750
6725x1550x2814
 Main components:Â
-Â Motor:Â Siemens, WEG, SEW
-Â Gear reducer:Â SEW, FALK
-Â Bearing:Â SKF, FAG, NSK
-Â Air cylinder:Â Festo, SMC, AirTac
-Â PLC interface and module:Â Siemens, Schneider, Beckhoff
-Â Frequency inverter:Â ABB, Schneider, Siemens
-Â Servo motor:Â Lenze, Delta
-Â Pressure sensor:Â Dynisco, Gefran
-Â Low voltage component:Â Siemens, Schneider, Omron, LS
-Â Temperature controller:Â Omron, RKC
-Â Solid state relay:Â Crydom, Celduc
About ACEEXTECH:
ACEEXTECH is a creative company, focusing on R & D of plastic extrusion system, and providing the equipments and solutions for plastic pipe, profile, tile, sheet and board.
ACEEXTECH products fulfill the needs of users in a very direct way due to over 25 years of knowledge and experience in plastic extrusion field, which also helps us to contribute actively to the success of customers by offering sustainable solutions that meet industry needs.   Â
ACEEXTECH offers a complete portfolio of support and consulting services all the time, from project engineering to custom financing solutions, after sales service at its best, ongoing production optimization, training and advisory services, even end product development.
Â
Why ACEEXTECH:
-Â Specialized RÂ & DÂ team involved in plastic extrusion industries over 25years.
-Â Ability to provide the customized plastic extrusion solutions
Plastic PVC Water Supply Pipe Machine
Model NO.: ACE-65/132-80/156-92/188
Motor Brand: Siemens,Weg,Sew
Gearbox: Vertical Type Sew/ Falk Brand
Inverter: ABB/Schneider/Siemens
Bearing: SKF,NSK
Barrel & Screw Material: Bimetallic Barrel & Screw
Output Capacity: 700kg/H
Raw Material: UPVC/CPVC/PVC Powder
Trademark: ACEEXTECH
Transport Package: Wooden Pallets
Specification: PVC pipe extrusion machine cost
Origin: China
HS Code: 8477209000
Model NO.: ACE-65/132-80/156-92/188
Motor Brand: Siemens,Weg,Sew
Gearbox: Vertical Type Sew/ Falk Brand
Inverter: ABB/Schneider/Siemens
Bearing: SKF,NSK
Barrel & Screw Material: Bimetallic Barrel & Screw
Output Capacity: 700kg/H
Raw Material: UPVC/CPVC/PVC Powder
Trademark: ACEEXTECH
Transport Package: Wooden Pallets
Specification: PVC pipe extrusion machine cost
Origin: China
HS Code: 8477209000
Plastic PVC water supply pipe machine