Many people in life have encountered this situation because they neglected their personal driving license. Have a driver's license to be able to drive, but the loss of driver's license does not mean that he does not have a driver's license, so it should be able to drive it? For the driver's license lost can drive a lot of people are arguing, some people think that, some people We think that we cannot do it. So, I lost my driver's license to drive? This article gives you a definitive answer. I lost my driver's license and I can't drive, but it takes a certain amount of time to lose my driver's license. If you can't drive during this time, you will have an impact on the lives and commuting of many people. What should I do? You can apply for a temporary driver's license, just like a temporary ID card. Specific procedures can be consulted with the local vehicle management office, or you can ask the local staff how to solve the situation when you renew your driver's license. In fact, the current driver's license replacement is very fast, and the fast one-day driver can get a good re-issued driver's license. There is no need to worry too much about the delayed re-issuance of the driver's license. Driver's license can not drive, driver's license can not drive around, can not drive, in other words if people want to drive on the road, the body must carry a driver's license, if you do not carry the driver's license on the road by the traffic police inquiries, then there may be deducted points Fine penalty. If the driver’s own driving license expired, he cannot drive. Driver’s license will be punished if he drives on the road after being expired. I lost my driver's license to drive it? It is recommended that after losing the driver's license is best not to try their own way, I feel that the opportunity to meet the traffic police is usually not, there is a chance that she can escape the robbery, drove around wandering, and other traffic police It was regretful to find it. Also, don't put your ID card and driver's license together. If the ID card and driver's license are lost at the same time, the time for re-applying the driver's license will be longer and the driver will not be able to drive longer. If your weld isn't on a piece of metal that will show, or if you don't care about how the weld looks, then you are done with your weld. However, if the weld is showing or you are welding something that you want to look nice then you will most likely want to grind down your weld and smooth it out. Welding Grinding,Tig Welding Helmet,Welding Grinding Helmet,Metal Welding Grinding Changzhou Edaweld Trading Company Limited , https://www.edaweld.com
Slap a grinding wheel onto an angle grinder and get started grinding on the weld. The neater your weld was the less grinding you will have to do, and after you have spent a whole day grinding, you will see why it's worth it to keep your welds neat in the first place. If you use a ton of wire and made a mess of things it's ok, it just means that you might be grinding for a while. If you had a neat simple weld though, then it shouldn't take too long to clean things up.
Be careful as you approach the surface of the original stock. You don't want to grind through your nice new weld or gouge out a piece of the metal. Move the angle grinder around like you would a sander so as not to heat up, or grind away any one spot of the metal too much. If you see the metal get a blue tinge to it you are either pushing too hard with the grinder or not moving the grinding wheel around enough. This is can happen especially easily while grinding thing sheets of metal.
Grinding welds can take a while to do depending on how much you have welded and can be a tedious process - take breaks while grinding and stay hydrated. (Grinding rooms in shops or studios tend to heat up, especially if you are wearing leathers). Wear a full face mask when grinding, a mask or respirator, and ear protection. Make sure that all your clothing is neatly tucked in and that you don't have anything hanging down from your body that could get caught in the grinder - it spins fast and it can suck you in!
When you are done your piece of metal might look something like the one in the second photo pictured below. (Or maybe better as this was done by a few Instructables Interns at the beginning of the summer during their first welding experience.)
Step 8: Common Problems